China wholesale Wheel Loader Broom Attachment - Cross shaft for wheel loader parts – CCMIC

cross shaft

Because there are many kinds of spare parts, we can’t display them all on the website. Please feel free to contact us for specific ones.

advantage

1. We supply both original and aftermarket products for you
2. From the manufacturer to the customer directly, saving your cost
3. Stable stock for normal parts
4. In Time Delivery Time, with competitive shipping cost
5. Professional and on time after service

packing

Carton Boxes, or according to clients’ request.

description

Also known as ten bytes, universal joint, the English name universal joint, is a part that realizes variable angle power transmission. It is used to change the position of the transmission axis direction. It is the “joint” of the universal transmission device of the automobile drive system. part. The cross-shaft rigid universal joint is a variable speed universal joint widely used in automobiles, and the maximum angle of intersection between two adjacent shafts is allowed to be 15゜～20゜. The cross shaft is one of the key parts of the cross shaft rigid universal joint.
The failure of the universal joint of the transmission shaft is mainly caused by the wear of the journal and the bearing and the bending and deformation of each journal, which causes the center lines of the cross shafts to be not on the same plane, or the center lines of the adjacent two shafts are not vertical. Because the universal joint cross shaft journal and bearing wear gap is too large, the cross shaft shakes during operation, which causes the center line of the transmission shaft to deviate from its rotation center line, causing the transmission shaft to vibrate and the transmission shaft to make abnormal noises during operation. phenomenon. Wear is mainly caused by lack of lubrication.
The wear of the universal joint cross shaft journal and bearing should not exceed 0.02～0.13mm from the point of view of use, and should generally be kept at about 0.01mm. If it exceeds 0.13mm, vibration and noise of the drive shaft will occur. If the cross shaft journal wears out of the groove, the groove is very deep and should be repaired or replaced. If surfacing and inlay repairs are used, heat treatment and grinding are also required. After processing, the out-of-roundness of each journal is required to be 0.01mm, and the taper cannot be large (the length of 20mm cannot be greater than 0.01mm). To check the verticality of two adjacent axes, be sure to ensure that they are vertical. After processing and repair, the axis of each journal should be in the same plane.
When the vehicle is running, because the direction of torque transmission is the same, the direction of force on the cross shaft is also the same. Over time, the unilateral wear of the cross shaft journal will be caused. As time goes by, the force side of the cross shaft will wear more and more, causing grooves, so that it will be loose and loud. You can use the cross shaft to rotate 90° relative to the original position, which can extend the use time. When assembling, pay attention to the side with the oil nozzle facing the drive shaft, the universal joint fork should rotate freely on the cross shaft, there should be no jamming phenomenon, and there should be no axial gap. Grease should be injected frequently in daily maintenance to prevent the wear of the cross shaft journal and bearings due to lack of grease.

our warehouse

Pack and ship

• Aerial Boom Lift
• China Dump Truck
• Cold Recycler
• Cone Crusher Liner
• Container Side Lifter
• Dadi Bulldozer Part
• Forklift Sweeper Attachment
• Hbxg Bulldozer Parts
• Howo Engine Parts
• Hyundai Excavator Hydraulic Pump
• Komatsu Bulldozer Parts
• Komatsu Excavator Gear Shaft
• Komatsu Pc300-7 Excavator Hydraulic Pump
• Liugong Bulldozer Parts
• Sany Concrete Pump Spare Parts
• Sany Excavator Spare Parts
• Shacman Engine Parts
• Shantui Bulldozer Clutch Shaft
• Shantui Bulldozer Connecting Shaft Pin
• Shantui Bulldozer Control Flexible Shaft
• Shantui Bulldozer Flexible Shaft
• Shantui Bulldozer Lifting Cylinder Repair Kit
• Shantui Bulldozer Parts
• Shantui Bulldozer Reel Shaft
• Shantui Bulldozer Reverse Gear Shaft
• Shantui Bulldozer Spare Parts
• Shantui Bulldozer Winch Drive Shaft
• Shantui Dozer Bolt
• Shantui Dozer Front Idler
• Shantui Dozer Tilt Cylinder Repair Kit
• Shantui Sd16 Bevel Gear
• Shantui Sd16 Brake Lining
• Shantui Sd16 Door Assembly
• Shantui Sd16 O-Ring
• Shantui Sd16 Track Roller
• Shantui Sd22 Bearing Sleeve
• Shantui Sd22 Friction Disc
• Shantui Sd32 Track Roller
• Sinotruk Engine Parts
• Tow Truck
• Xcmg Bulldozer Parts
• Xcmg Bulldozer Spare Parts
• Xcmg Hydraulic Lock
• Xcmg Transmission
• Yuchai Engine Parts